Opel Vectra A

since 1988-1995 release

Repair and operation of the car


Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   + 16:35. Replacement of protection covers of steering transfer
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


16.3. Replacement of the bearing of a forward wheel

Removal

Expression of a nave of a forward wheel from the bearing

Removal internal a bearing ring from a nave

Unscrewing of the screw of fastening of a protective board of a brake disk

Removal of the lock ring fixing an external ring of the bearing

PERFORMANCE ORDER
1. Remove a rack of a forward suspension bracket together with a rotary fist.
2. Unscrew the screw and remove a brake disk from a nave.
3. For extraction of a nave from a rotary fist use a press and a tubular mandrel of the corresponding diameter. Establish a rotary fist on steel cores by inside up and, using a metal mandrel, squeeze out a nave from hug bearings (see rice. Expression of a nave of a forward wheel from the bearing).
4. Using a stripper, remove an internal ring of the bearing from a nave (see rice. Removal internal a bearing ring from a nave).
5. Unscrew three screws and remove a protective board of a brake disk from a rotary fist (see rice. Unscrewing of the screw of fastening of a protective board of a brake disk).
6. Remove the lock rings fixing an external ring of the bearing from a rotary fist (see rice. Removal of the lock ring fixing an external ring of the bearing).
7. Opiry an internal part of a rotary fist on supports and using a tubular mandrel of the corresponding diameter, squeeze out an external ring of the bearing from a rotary fist.

Installation

Arrangement of the hug bearing of a forward wheel
 And – an external lock ring of the bearing;
In – an internal lock ring of the bearing

Installation of the hug bearing of a forward wheel from an ispolzov niy a tubular mandrel, a nut, a bolt and washers of the corresponding diameter

Installation of a nave of a forward wheel with use of a tubular mandrel, nut, bolt and washers of the corresponding diameter

PERFORMANCE ORDER
1. Clear a nave and a rotary fist of dirt, and lubricant. Establish an external lock ring of fastening of the bearing (see rice. Arrangement of the hug bearing of a forward wheel). Keep in mind that uvulas of a lock ring have to be turned to the basis of a rotary fist.
2. Reliably fix a rotary fist on supports and install on it the bearing. You make installation of the bearing with use of a tubular mandrel which has to press on an external ring of the bearing. The bearing install against the stop it in an external lock ring (see rice. Installation of the hug bearing of a forward wheel from an ispolzov niy a tubular mandrel, a nut, a bolt and washers of the corresponding diameter).
3. Establish an internal lock ring of the bearing that uvulas of a lock ring were turned to the basis of a rotary fist.
4. Establish a protective board of a brake disk.
5. Install a nave in the bearing. At the same time use a tubular mandrel which presses on an internal ring of the bearing. The nave press fitting in the bearing can be made with use of a long bolt, nut and washers of the corresponding diameter (see rice. Installation of a nave of a forward wheel with use of a tubular mandrel, nut, bolt and washers of the corresponding diameter).
6. Establish a brake disk.
7. Install a rack of a forward suspension bracket with a rotary fist on the car.