п»ї The device, service, repair Vektr's Opel And - 16.13. Replacement of the hug bearing of a back wheel (model since 1993)//1988-1995 /

Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   + 16:35. Replacement of protection covers of steering transfer
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775 Покрасочное оборудование вагнер окрасочное оборудование вагнер. 24bec775 Покрасочное оборудование вагнер окрасочное оборудование вагнер.



16:13. Replacement of the hug bearing of a back wheel (model since 1993)

GENERAL INFORMATION

Prevention

At installation it is necessary to use new nuts of fastening of the fastener of a nave.


Non-demountable knot of a nave and the bearing of a back wheel on late models with ABS

1 – nave;
2 – nave fastener;
3 – bolt;
4 – a dustproof cap with the ABS sensor;
5 – bearing;
6 – sealing ring

Removal

PERFORMANCE ORDER
1. Since 1993 on all models of an ustanavla the non-demountable knot of a nave and the bearing of a back wheel is howled (see the drawing).
2. As the knot consisting of the fastener of a nave of a nave and the hug bearing is non-demountable knot, adjustment of the bearing is not required.
3. Take off a wheel cap, then weaken bolts of fastening of a wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.
4. Remove a support of a back disk brake. Without disconnecting a brake hose from a support, using a soft wire, tie up a support to a back suspension bracket, at the same time do not stretch and overwind a brake hose.
5. Remove a returnable spring from the lever of a block of the emergency brake and a brake board.
6. Unscrew the screw and remove a brake disk.
7. Disconnect the electric socket from the ABS sensor.
8. Unscrew four nuts and remove nave knot together with a brake board. As soon as there is an access, disconnect a cable of the emergency brake from the lever of a block of the emergency brake.

Installation

Installation is made in the sequence, the return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Tighten nuts of fastening of knot of a nave the required moment.
2. Check correctness of connection of a cable of the emergency brake and a returnable spring.
3. Establish a brake disk and a support of a brake.
4. Check adjustment of a cable of the emergency brake, then establish a wheel and lower the car on the earth.