The device, service, repair Vektr's Opel And - 16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket//1988-1995 /

Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   + 16:35. Replacement of protection covers of steering transfer
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775 24bec775



16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
(models with SOHC engines)

GENERAL INFORMATION

Cutting of an internal flange from the plug of fastening of the longitudinal lever of a back suspension bracket

The correct arrangement of ledges on the plug of the longitudinal lever on models with the SOHC engine

Replacement of the plug of the longitudinal lever of a back suspension bracket can be made without removal of a back torsion beam.

PERFORMANCE ORDER
1. In the presence take off caps, then weaken bolts of fastening of back wheels. Lift a back part of the car and fix on supports. Remove back wheels.
2. On models with the self-leveled back suspension bracket take off pressure in system, having let out the air via the valve in the luggage compartment.
3. Disconnect brake hoses and the back ends of brake tubes from the car bottom.
4. Support by a jack through wooden whetstone a back torsion beam.
5. Unscrew nuts and take bolts, the fixing forward parts of longitudinal levers of a back suspension bracket to the car bottom.
6. Lower a jack so that access to plugs of longitudinal levers of a back suspension bracket was possible. Be careful that when lowering a jack not to deform brake tubes. For removal and installation of plugs it is desirable to use the special Opel tool. In the absence of the special tool replacement of plugs can be made with use of a long bolt, nut, washers and a piece of a steel tube of the corresponding diameter.
7. Before removal cut off a flange since the internal end of the plug (see rice. Cutting of an internal flange from the plug of fastening of the longitudinal lever of a back suspension bracket).
8. For simplification of removal of the plug heat a plug casing in the longitudinal lever of a back suspension bracket to 70 °. For heating do not use an open flame as a row located the fuel tank.
9. Take the plug from the longitudinal lever of a back suspension bracket.
10. Moisten the new plug with soap water and establish it into place so that ledges at an end face of the plug were located as shown in rice. The correct arrangement of ledges on the plug of the longitudinal lever on models with the SOHC engine.
11. Similarly replace the plug from the second party of the car. Replacement of plugs has to be made in pairs.
12. Using a jack, lift a back torsion beam and fix by bolts. Screw on nut bolts, without tightening them it is final. Take a jack from under the car.
13. Fix brake tubes and brake hoses on the car bottom.
14. Establish back wheels, then lower the car on the earth and tighten bolts of fastening of wheels the required moment.
15. On models with the self-leveled back suspension bracket increase in system pressure to 0,8 bars.
16. Install the car on the flat horizontal platform, then arrange freight weighing 70 kg on each forward sitting and shake the car in order that all elements of a back suspension bracket rose on the places.
17. Working under the car, an okonchatel but tighten nuts on the bolts fixing forward parts of longitudinal levers of a back suspension bracket to the car bottom.