Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
- 4. Repair of the diesel engine
   4.2. General information
   4.3. The repair which is not demanding removal of the engine
   4.4. Check of a compression
   4.5. Top Dead Point (TDP) of the piston of the first cylinder
   4.6. Cover of a head of the block of cylinders
   4.7. Pulley of a bent shaft
   4.8. Casings of a gear belt
   4.9. Replacement of a gear belt
   4.10. Check and installation of phases of gas distribution
   + 4.11. Mechanism of a tension of a gear belt and pulleys
   4.12. Replacement of a sealing ring of the camshaft
   4.13. Check and adjustment of gaps of valves
   4.14. Camshaft and pushers
   4.15. Head of the block of cylinders
   4.16. Oil pallet
   4.17. Oil pump
   4.18. Replacement of a sealing ring of the oil pump
   4.19. Oil heater
   + 4.20. Pistons with rods
   4.21. Flywheel
   4.22. Replacement of sealing rings of a bent shaft
   4.23. Replacement of support of the power unit
   4.24. Recommendations about removal of the engine
   4.25. Removal and installation of the engine
   4.26. Repair of the engine
   4.27. Start of the engine after capital repairs
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


4.14. Camshaft and pushers

GENERAL INFORMATION

Sequence of tightening of nuts of fastening of covers of bearings of the camshaft

Removal

Removal of a cover of the bearing of the camshaft

PERFORMANCE ORDER
1. Uncover a head of the block of cylinders.
2. Remove a camshaft pulley.
3. Unscrew bolts of fastening of a back casing of a gear belt to a head of the block of cylinders.
4. Working in a certain sequence, weaken nuts of fastening of covers of bearings of the camshaft on a half of a turn for each pass before full unscrewing of nuts. It is necessary for gradual and uniform removal of pressure of valvate springs.
5. Uncover, checking their marking. On covers of bearings are put figure from 1 to 5 and the shooter which is directed to a gear belt (see rice. Removal of a cover of a podshipna of the camshaft).
6. Remove the camshaft from a head of the block of cylinders. Take pushers from nests in the top part of a head of the block of cylinders and place them in the numbered plastic bags for repeated installation on the places.

Check

PERFORMANCE ORDER
1. Check a condition of working surfaces of bearings of the camshaft and cams for wear existence. With any wear on distributive to a shaft it is subject to replacement. Check a condition of workers poverkhno sty bearings of the camshaft of a head of the block of cylinders. If the working surfaces of bearings are worn-out, it is necessary to replace a head of the block of cylinders
2. Check a condition of pushers. If on pushers there is a wear, the pusher needs to be replaced.

Installation

Installation of a pusher in a head of the block of cylinders

Installation of adjusting laying in a pusher glass

Greasing of bearings of the camshaft in a head of the block of cylinders

Places of putting sealant (arrow) on a head of the block of cylinders and the provision of an adjusting pin of the camshaft (A)

PERFORMANCE ORDER
1. Oil pushers pure engine and establish them on the initial places. Check that in the top part of pushers are established регулиро vochny laying (see rice. Installation of a pusher in a head of the block of cylinders, Installation of adjusting laying in a pusher glass).
2. Grease camshaft bearings in a head of the block of cylinders with pure engine oil and install the camshaft (see rice. Greasing of bearings of the camshaft in a head of the block of cylinders). Check that the tag on a pulley of a bent shaft is combined with the index on the case of the oil pump, and the pulley of the fuel pump is recorded by a tightening bolt. Install the camshaft so that cams of the first cylinders were directed up and the adjusting pin at an end face of the camshaft was also directed up.
3. Grease bearings and cams of the camshaft are pure engine oil.
4. Apply a thin film of sealant on a head of the block of cylinders in the field of installation of a cover of the first bearing to a raspreda of a litelny shaft (see rice. Places of putting sealant on a head of the block of cylinders and the provision of an adjusting pin of the camshaft).
5. Establish covers of bearings of the camshaft. At the same time shooters on covers have to be directed to a gear belt.
6. Tighten nuts of fastening of covers of bearings by hand. Evenly and gradually (every time on one turn) tighten covers of bearings distribute a telny shaft to a contact them with a head of the block of cylinders. After that in a certain sequence tighten all nuts in several stages the required moment.
7. Establish a new oil sealing ring of the camshaft.
8. Screw bolts of fastening of a back casing of a gear belt on a head of the block of cylinders.
9. Establish a pulley of the camshaft and a gear belt.
10. Check gaps of valves and establish a cover of a head of the block of cylinders.