Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   - 2.9. Removal and installation of the engine together with the transmission
      2.9.1. Removal
      2.9.2. Separation of the transmission from the engine
      2.9.3. Connection of the transmission with the engine
      2.9.4. Installation
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775



2.9.3. Connection of the transmission with the engine

PERFORMANCE ORDER
1. Using a tap of M10x1,25 clear two openings in a body for fastening of the left rubber pillow of the transmission.
2. On models with the automatic transmission if from the hydrotransformer liquid flowed out, fill in it to the maximum level. For an exception of damage of a sealing ring of an entrance shaft of the transmission wipe the plug of the hydrotransformer and install the hydrotransformer so that he correctly united to shaft.
3. If replacement of the transmission was made, clear channels of an additional radiator of cooling of transmission liquid for what it is possible to use compressed air under low pressure, but at the same time be careful not to deform a radiator.
4. Using a tap of M10x1,25 clear a carving in fastening openings гидротран a sformator and prepare new bolts of fastening.
5. Tighten nuts and bolts the required moment. When tightening bolts of fastening of the hydrotransformer to a plate of the drive it is necessary to use the special extender see rice. Use of the special extender for tightening of bolts of fastening of the hydrotransformer).
6. If coupling is screwed by bolts on a flywheel, be careful that the transmission did not freeze up on entrance to a shaft.
7. Install the transmission on the engine and fix by bolts, having tightened them the required moment.
8. Establish a protective cover of a case of coupling.