Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   + 2.9. Removal and installation of the engine together with the transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


2.29. Repair of the oil pump

GENERAL INFORMATION

Prevention

At installation of the oil pump use a new sealing ring of a bent shaft.


Dismantling

Unscrewing of screws of fastening of a back cover of the oil pump on the engine of 2,0 l

PERFORMANCE ORDER
1. Remove the oil pump.
2. Unscrew screws and uncover the oil pump (see rice. Unscrewing of screws of fastening of a back cover of the oil pump on the engine of 2,0 l).

Check

Measurement of a gap between teeths of rotors of the oil pump

Measurement of an axial gap of a rotor of the oil pump

Details of the safety valve of pressure on the engine of 2,0 l

PERFORMANCE ORDER
1. Using a marker, note arrange ny an internal and external rotor of the oil pump.
2. Clear all details of the oil pump and check their state.
3. Using a probe edge, measure a gap between an internal and external rotor of the oil pump. Using металличес I forge a ruler, check an axial gap between the case of the oil pump and rotors (see rice. Measurement of a gap between teeths of rotors of the oil pump, Measurement of an axial gap of a rotor of the oil pump).
4. Unscrew a bolt of the safety valve of pressure from a forward part of the case of the oil pump and take a spring and a plunger from a pump housing (see rice. Details of the safety valve of pressure on the engine of 2,0 l).
5. Boots of natyazhitel have to rotate freely on axes. If on them there are cracks, chips or considerable wear of a working surface, they need to be replaced.

Assembly

Use of an edge of the screw-driver for removal of an old sealing ring from the case of the oil pump

Use of a tubular mandrel for installation of a new sealing ring of a bent shaft on the engine of 2,0 l

PERFORMANCE ORDER
1. Replace the forward sealing ring of a bent shaft located from the forward party of the case of the oil pump. Using a screw-driver edge, take an old sealing ring and, using a tubular mandrel of the corresponding diameter, establish a new sealing ring (see rice. Use of an edge of the screw-driver for removal of an old sealing ring from the case of the oil pump, Use of a tubular mandrel for installation of a new sealing ring of a bent shaft on the engine of 2,0 l).
2. Check that the interfaced surfaces of a back cover of the pump and a pump housing pure and dry, then apply a thin film of sealant (Opel No. 90485251) on these surfaces and install a back cover on the pump. Screw in screws of fastening of a cover.
3. Install the pump on the engine.