Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   + 2.9. Removal and installation of the engine together with the transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


2.17. Back sealing ring of the camshaft

Removal

PERFORMANCE ORDER
1. The back sealing ring of the camshaft can be replaced on the engine installed in the car after removal of the distributor of ignition.
2. Remove the ignition distributor.
3. On l models 1,4 and 1,6 except the C16 NZ2 engine the sealing ring is established in a back part of the case of the distributor of ignition. Using an edge of the thin screw-driver, take an old sealing ring.
4. On the C16 NZ2 models 1,8 and 2,0 of l using an edge of the thin screw-driver, take a sealing ring from the camshaft case.

Installation

PERFORMANCE ORDER
1. On l models 1,4 and 1,6 except C16 NZ2 engines establish a new sealing ring, and then establish to a raspreda a litel of ignition.
2. On the C16 NZ2 models 1,8 and 2,0 of l establish a new sealing ring so that it was up to standard with the case, then establish ignition distributor elements.