Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   + 2.9. Removal and installation of the engine together with the transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


2.27. Oil pallet

GENERAL INFORMATION

Prevention

At installation of the oil pallet it is necessary to use new laying and sealant at installation of the oil pump and back radical bearing.


Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Merge engine oil from the engine, then establish into place a masloslivny stopper and tighten it the required moment.
3. Tighten the emergency brake, then lift a forward part of the car and record on supports.
4. Remove a reception exhaust pipe.
5. In the presence disconnect the electric socket from the sensor of level of the engine oil installed in the oil pallet.
6. Unscrew bolts and remove a protective plate of coupling.
7. Evenly and gradually unscrew bolts of fastening and remove the oil pallet. Keep in mind that on the majority of models the reflector of oil of the oil pallet can be moved on considerable distance from the block of cylinders together with the oil pallet, but it cannot be removed until the maslozaborny phone of the oil pump is picked up.
8. On l models 1,6, 1,8 and 2,0 for removal of a reflector of oil it is necessary to unscrew the arm fixing a maslozaborny tube of the oil pump to the block of cylinders. The reflector of oil can be removed through a maslozaborny tube. On the l C16 NZ2 models 1,8 and 2,0 with an oil reflector the screw-driver remove rubber laying.
9. For removal of a maslozaborny tube of the oil pump unscrew a bolt, the fixing arm to the block of cylinders and two bolts fixing the end of a maslozaborny tube to the oil pump. Remove condense a telny ring of round section.
10. Clear the interfaced surfaces of the block of cylinders, a reflector of oil and the oil pallet of traces of old laying and sealant.

Installation

Places of putting sealant on the interfaced surfaces of the oil pump and a back cover of the radical bearing

Drawing a layer of sealant on the interfaced surface of the oil pump and block of cylinders of the engine on the engine of 2,0 l

Installation of new rubber laying on an oil reflector on the engine of 2,0 l

Installation of a new sealing ring of round section on a maslozaborny tube

Tightening of bolts of fastening of a maslozaborny tube on the engine of 2,0 l

Installation of an arm of fastening of a maslozaborny tube on the engine of 2,0 l

Drawing on a carving of bolts of fastening of the oil pallet of the means interfering their unscrewing

Installation of the oil pallet on the engine of 2,0 l

PERFORMANCE ORDER
1. Apply a thin film of Opel No. 90485251 sealant on the interfaced surfaces between the oil pump and the block of cylinders and between a back cover of the radical bearing and the block of cylinders (see rice. Places of putting sealant on the interfaced surfaces of the oil pump and a back cover of the radical bearing, Drawing a layer of a germeta on the interfaced surface of the oil pump and block of cylinders of the engine on the engine of 2,0 l).
2. On the C16 NZ2 models 1,8 and 2,0 of l establish new rubber laying on oil reflector perimeter (see rice. Installation of new rubber laying on an oil reflector on the engine of 2,0 l).
3. On models 1,6, 1,8 and 2,0 of l install an oil reflector in the block of cylinders, moving it through an intaking tube of the oil pump.
4. If the maslozaborny phone was picked up, install it on the oil pump with a new sealing ring of round section and fix by bolts, having tightened them the required moment (see rice. Installation of a new sealing ring of round section on a maslozaborny tube, Tightening of bolts of fastening of a maslozaborny tube on the engine of 2,0 l).
5. In the presence, establish an arm of fastening of a maslozaborny tube to the block of cylinders (see rice. Installation of an arm of fastening of a maslozaborny tube on the engine of 2,0 l).
6. Apply on a carving of bolts of fastening of the oil pallet means, to a prepyatstvo yushchy to their unscrewing (Opel No. 90167347), then install the oil pallet and fix by bolts, having tightened them the required moment (see rice. Drawing on a carving of bolts of fastening of the oil pallet of the means interfering their unscrewing, Installation of the oil pallet on the engine of 2,0 l).
7. If the engine is installed in le's avtomob, further installation is made in the sequence, the return to removal. Fill in engine oil in the engine.