Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance - 2. Engine 2.2. General information 2.3. System of ventilation of a case 2.4. Check of a compression 2.5. Repair operations on the engine installed in the car 2.6. The repair operations demanding removal of the engine 2.7. Recommendations about removal of the engine + 2.8. Removal and installation of the engine without transmission + 2.9. Removal and installation of the engine together with the transmission 2.10. Replacement of support of the engine and transmission 2.11. Repair of the engine - 2.12. A gear belt and pulleys (without automatic mechanism of a tension) 2.12.2. Installation 2.12.3. Adjustment of a tension 2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2) 2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6 2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0) 2.16. Forward sealing ring of the camshaft 2.17. Back sealing ring of the camshaft 2.18. Camshaft and case of the camshaft + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car 2.20. Removal and installation of a head of the block of cylinders on the removed engine + 2.21. Repair of a head of the block of cylinders 2.22. Cleaning and survey of a head of the block of cylinders 2.23. Hydraulic pushers of valves 2.24. Flywheel 2.25. Replacement of a forward sealing ring of a bent shaft 2.26. Replacement of a back sealing ring of a bent shaft 2.27. Oil pallet 2.28. Oil pump 2.29. Repair of the oil pump 2.30. Removal and installation of pistons and rods 2.31. Check of pistons and rods + 2.32. Removal and installation of a bent shaft 2.33. Check of a bent shaft 2.34. Survey and check of a gap in radical and conrod bearings 2.35. Check of a working gap of the bearing 2.36. Check of the block of cylinders of the engine 2.37. Start of the engine after capital repairs + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system + 6. Fuel system + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine + 10. Engine electrical systems + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system + 16. Suspension bracket + 17. Body + 18. Electric equipment + 19. Check of malfunctions
|
Installation of a persistent washer on a bent shaft
Installation of a segment spline on a bent shaft
Installation of a pulley of a gear belt on a bent shaft
Installation of a washer and bolt of fastening of a pulley of a bent shaft
Tightening of a bolt of fastening of a pulley of a bent shaft the required moment
Tightening of a bolt of fastening of a pulley of a bent shaft its dovorachivaniye on the required corner
Installation of a pulley of a bent shaft, a nave outside, on the engine of 1,6 l
Installation of a pulley of the camshaft
Tightening of a bolt of fastening of a pulley of the camshaft on the engine of 2,0 l
Installation of laying of a cover of a head of the block of cylinders
Tightening of bolts of fastening of a cover of a head of the block of cylinders
Installation of a gear belt on the engine of 2,0 l
Installation of a pulley of a bent shaft on the engine of 1,6 l
Screwing up of bolts of fastening of a pulley of a bent shaft on the engine of 2,0 l
PERFORMANCE ORDER |
1. Establish back casings of a gear belt in the sequence, the return to removal. Check that the main cover was correctly combined with a cover on the water pump. |
2. On C16 NZ2 engines 1,8 and 2,0 of l establish a persistent washer (see rice. Installation of a persistent washer on a bent shaft) and a segment spline on an end face of a bent shaft (see rice. Installation of a segment spline on a bent shaft). Establish a pulley of a bent shaft (see rice. Installation of a pulley of a gear belt on a bent shaft) also fix it by a bolt with a washer, having tightened a bolt the required moment in two stages. For keeping of a bent shaft from a provorachivaniye when tightening a bolt the assistant has to include any transfer and press a brake (see rice. Installation of a washer and bolt of fastening of a pulley of a bent shaft, Tightening of a bolt of fastening of a pulley of a bent shaft the required moment, Tightening of a bolt of fastening of a pulley of a bent shaft its dovorachivaniye on the required corner). |
3. On l engines 1,4 and 1,6 except a dvigata leu of C16 NZ2 establish a segment spline and a pulley of a bent shaft on a bent shaft (see rice. Installation of a pulley of a bent shaft on the engine of 1,6 l). |
4. Establish a camshaft pulley, at the same time an adjusting pin on distributive to a shaft has to enter an opening of a pulley and fix a pulley by a bolt, having tightened it the required moment (see rice. Installation of a pulley of the camshaft, Tightening of a bolt of fastening of a pulley of the camshaft on the engine of 2,0 l). When tightening a bolt of fastening of a pulley hold the camshaft from a provorachivaniye a wrench for vents between cams of the third and fourth cylinders. Check a condition of laying of a cover of a head of the block of cylinders and, if necessary, replace it. Establish laying and a cover of a head of the block of cylinders (see rice. Installation of laying of a cover of a head of the block of cylinders). Establish arms of fastening of high-voltage wires under bolts of fastening of a cover of a head of the block of cylinders and screw a cover bolts (see rice. Tightening of bolts of fastening of a cover of a head of the block of cylinders). Connect a hose of ventilation of a case to a cover of a head of the block of cylinders. |
5. Temporarily establish a pulley of a vspomog of a telny driving belt on a bent shaft and check that adjusting tags on a pulley of a bent shaft and a pulley of the camshaft are combined with indexes. Remove a pulley vspomogatelno about a driving belt from a bent shaft, then put on a gear belt on pulleys, since a pulley of a bent shaft (see rice. Installation of a gear belt on the engine of 2,0 l). |
6. Establish a pulley of an auxiliary driving belt on a bent shaft and fix by bolts, having tightened them the required moment. For keeping of a bent shaft of the engine from a provorachivaniye when tightening bolts of fastening of a pulley of a bent shaft the assistant has to include any transfer and press a brake (see rice. Installation of a pulley of a bent shaft on the engine of 1,6 l, Screwing up of bolts of fastening of a pulley of a bent shaft on the engine of 2,0 l). |
7. Adjust a tension of a gear belt. |
8. On models with the engine of 1,6 l with the amplifier of steering install the pump of the amplifier of steering. |
9. Establish an external casing of a gear belt, and on C16 NZ2 engines 1,8 and 2,0 of l connect the electric socket to the sensor of the index of temperature. |
10. Establish a driving belt of the generator and adjust its tension. |
11. On l C16 NZ2 engines 1,8 and 2,0 with the amplifier of steering establish a driving belt of the pump of the amplifier of steering and adjust its tension. |
12. Connect a weight wire to the accumulator. |
|
|
|