|
Opel Vectra Asince 1988-1995 releaseRepair and operation of the car |
|
Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance + 2. Engine + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system - 6. Fuel system 6.2. General information 6.3. Air filter 6.4. The block of adjustment of temperature of the air coming to the engine 6.5. Check of the fuel pump 6.6. Removal and installation of the fuel pump 6.7. Fuel tank 6.8. Fuel level sensor 6.9. Separator of vapors of fuel (l models 1,6 and 1,8) 6.10. Accelerator pedal 6.11. Accelerator cable 6.12. Carburetor 6.13. Removal and installation of the carburetor 6.14. Adjustment of turns of idling and contents WITH 6.15. Needle and float 6.16. Vacuum diaphragm of a butterfly valve of the secondary camera 6.17. Economizer diaphragm 6.18. Accelerating pump 6.19. Knot of the air automatic gate + 6.20. Vacuum blocks of movement of the air automatic gate 6.21. Carburetor filter 6.22. Adjustment of the shock-absorber of a butterfly valve 6.23. Sensor of provision of a butterfly valve (automatic transmission) 6.24. Valve check of increase in turns of idling 6.25. The electromagnetic valve of idling on models of 1,8 l 6.26. Inlet collector + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine + 10. Engine electrical systems + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system + 16. Suspension bracket + 17. Body + 18. Electric equipment + 19. Check of malfunctions |
6.12. Carburetor
Arrangement of the accelerating pump (1) and diaphragm block of movement of the main gate (2) Arrangement of the case of the automatic air gate (1), separator of vapors of fuel (2) and vacuum diaphragm of a secondary butterfly valve (3) Winding of movement of the secondary gate (1) and valve of the economizer (2) The PIERBURG 2E3 carburetor – two-chamber with the calibrated jets and butterfly valves opening consistently. The butterfly valve of the secondary camera opens only at high turns of the engine under loading. Consecutive opening of butterfly valves provides high economy of fuel at smooth acceleration and uniform motion, and also provides the maximum engine capacity by full pressing of a pedal of an accelerator. The control of the secondary gate is made by vacuum in primary camera. Diameters of elements of primary camera of the carburetor it is less, than secondary. The carburetor is a difficult unit in which there are many systems for providing the operational modes of the engine (see rice. Arrangement of the accelerating pump and diaphragm block of movement of the main gate, Arrangement of the case of the automatic air gate, separator of vapors of fuel and vacuum diaphragm of a secondary butterfly valve, Winding of movement of the secondary gate and valve of the economizer). The system of idling of the carburetor works irrespective of other systems and is run by the screw of adjustment of quality of mix. Calibration of the main jets is made so that the engine worked normally at a half-open butterfly valve. For ensuring giving of the required amount of fuel at the maximum acceleration the vacuum valve of the economizer is used. The valve gives additional amount of fuel at the maximum depression at completely open butterfly valves. For increase in supply of fuel at acceleration the accelerating pump gives additional fuel to the main diffuser of primary camera. The control of the accelerating pump is made mechanically by a cam from draft of a butterfly valve. For management of position of the air gate the automatic mechanism, is used by the coping cooled liquid and the lichesky spring which is heating up bimetal. On a cold dvigat of le the bimetallic spring is completely compressed and holds the gate in primary camera in a closed position. In process of warming up of the engine the bimetallic spring extends and opens the air gate of the first camera. Supply of vacuum copes system of movement. At the same time if the engine works with slightly slightly opened gate at uniform motion of the car under small loading the gate is slightly opened and protivody stvut to a bimetallic spring. The system of movement excludes pereobogashche ny fuel mix. The secondary winding of system of movement is used together with the main block of a diaphragm for change of characteristics of system of movement for increase in economy of fuel. On engines of 1,8 l there is a cut-off valve. It is the electromagnetic valve which blocks supply of fuel mix in system of idling at switching off of ignition. |
|