Opel Vectra A

since 1988-1995 release

Repair and operation of the car


Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   + 2.9. Removal and installation of the engine together with the transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   - 2.21. Repair of a head of the block of cylinders
      2.21.2. Assembly
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775


2.21.2. Assembly
GENERAL INFORMATION

Installation of the final valve in a head of the block of cylinders

Installation of the lower cup of a spring

Installation of the adjusting plug on a valve core

Installation of a maslootrazhatelny cap

Installation of a maslootrazhatelny cap into place

Installation of a valvate spring

Installation of the top cup of a spring

Installation of crackers in dredging of a core of the valve

PERFORMANCE ORDER
1. Clear all details of a head of the block of cylinders.
2. Oil cores of valves engine and insert them on the places. Install the valve on those places where they were ground in (see rice. Installation of the final valve in a head of the block of cylinders).
3. Install the lower cup of a spring (see rice. Installation of the lower cup of a spring).
4. In a set of new maslootrazhatelny caps there is an adjusting plug which is installed on a core of the valve and protects working edges of maslootrazhatelny caps at their installation. Install the adjusting plug on a valve core (see rice. Installation of the adjusting plug on a valve core). Lower a maslootrazhatelny cap in fresh engine oil and establish it on a valve core into place, being careful not to damage its working edges. For installation of maslootrazhatelny caps use a special metal mandrel (see rice. Installation of a maslootrazhatelny cap, Installation of a maslootrazhatelny cap into place).
5. Establish a valvate spring and the top cup of a spring (see rice. Installation of a valvate spring, Installation of the top cup of a spring).
6. Special adaptation squeeze a valvate spring and establish crackers in dredging of a core of the valve and grease them. Remove the device for compression of a spring. Repeat this operation on other valves.
7. Knock with a hammer through wooden whetstone on a valve core end face in order that all elements of the valve accurately were established on the places (see rice. Installation of crackers in dredging of a core of the valve).
8. If necessary establish collectors, the thermostat and a casing of the thermostat. Screw in spark plugs.
9. Install a head of the block of cylinders on the engine.