Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures when carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cowl lock cable
   17:10. Trunk lid (Sedan models)
   17:11. Lock of a trunk lid (Sedan model)
   17:12. Cylinder of the lock of a trunk lid (Sedan model)
   17:13. Back door (Hatchback models)
   17:14. Lock of a back door (Hatchback model)
   17:15. Cylinder of the lock of a back door (Hatchback model)
   17:16. Racks of a back door (Hatchback model)
   17:17. Doors
   17:18. Door upholstery
   17:19. Internal handle of opening of a door
   17:20. External handle of opening of a door
   17:21. Door lock cylinder
   17:22. Door lock
   17:23. Limiter of opening of a door
   17:24. Wind and back flew down
   17:25. Back triangular window leaves
   17:26. Door glass
   17:27. Window regulators
   17:28. External rear-view mirror
   17:29. Bumpers
   17:30. Front grille
   17:31. Windshield deflector
   17:32. Wheel arch inserts
   17:33. Lower protective plate (mudguard) of the engine
   17:34. Folding shutter of a fuel-filling mouth of the fuel tank
   + 17:35. Hatch elements
   17:36. Finishing of an interior
   - 17:37. Panels of finishing of the dashboard
      17.37.2. The lower panel of finishing from the driver
      17.37.3. Casings of a steering column
      17.37.4. Lower panel of finishing of a combination of devices
      17.37.5. Top panel of finishing of a combination of devices
      17.37.6. Lighting switching block
      17.37.7. Radio receiver pocket
      17.37.8. Ware box
   17:38. Central console
   17:39. Ceiling
   17:40. Sitting (without mechanisms of a tension of seat belts)
   17:41. Seat belts
   17:42. Seat belt tension mechanism
   17:43. Forward sitting with the seat belt tension mechanism
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


17.37.7. Radio receiver pocket

Removal

Arrangement of the right adjusting pin behind the control panel of a heater

Removal of the panel of finishing of the radio receiver

Removal of a pocket of the radio receiver from the dashboard

Detachment from a pocket of the radio receiver of the electric socket and the antenna plug

PERFORMANCE ORDER
1. Remove the radio receiver.
2. Remove the lower and top panels of finishing of a combination of devices.
3. Unscrew the fastening screw from the lower right side of the control panel of a heater.
4. Remove from the dashboard hours or the on-board computer.
5. Through an aperture for hours or the on-board computer unscrew two screws of fastening of the control panel of a heater.
Being careful, move the control panel of a heater within length of wires forward and take it from the dashboard, at the same time do not stretch a cable of management of a heater. Adjusting pins of the panel of finishing of the radio receiver are behind adjusting pins of the control panel of a heater (see rice. An arrangement of the right adjusting pin behind the control panel of a heater, Removal of the panel of finishing of the radio receiver).
In the presence unscrew two screws and, having pulled forward, take a radio receiver pocket, then disconnect from it the electric socket and the plug of the antenna (see rice. Removal of a pocket of the radio receiver from the dashboard, the Detachment from a pocket of the radio receiver of the electric socket and the antenna plug).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.