Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.33. The step engine of management of air supply on idling turns

Removal

Detachment of the electric socket from the step engine of management of air supply on idling turns

Unscrewing of screws of fastening of the step engine

Removal of the step engine
The arrow showed a sealing ring.

PERFORMANCE ORDER
1. Remove the heater block.
2. Remove a weight wire from the accumulator.
3. Disconnect the electric socket from the step engine (see rice. A detachment электричес whom the socket from the step engine of management of air supply on idling turns).
4. Unscrew two screws and remove the step engine. Remove a sealing ring from the step engine (see rice. Unscrewing of screws of fastening of the step engine, Removal of the step engine).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal taking into account the next moments:

– install a new sealing ring on the step engine and apply on it a thin film of lubricant for simplification of installation of the step engine;
– for an exception of damage of the case of a throttle or a tip of a plunger of the step engine which acts more than on 28 mm from the interfaced surface of the step engine, being careful, press a plunger inside against the stop. After start of the engine the step engine needs to be installed in a starting position, using signals from the ECU block;
– before a vvinchivaniye of screws of fastening of the step engine apply the means interfering their unscrewing on a carving of screws.