Opel Vectra A

since 1988-1995 release

Repair and operation of the car

Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

7.25. Air stream measuring instrument

GENERAL INFORMATION

Prevention

At installation of a bell of an air inlet establish new laying. Before a vvinchivaniye of bolts of fastening of the measuring instrument of a stream of air apply the means interfering their unscrewing on a carving of bolts.

Removal

Arrangement of a bolt of fastening of the measuring instrument of a stream of air on the SOHC models

Arrangement of bolts of fastening of the measuring instrument of a stream of air

PERFORMANCE ORDER

1. Remove the air filter.

2. Unscrew a bolt, the fixing air stream measuring instrument to a cover of the air filter (see rice. An arrangement of a bolt of fastening of the measuring instrument of a stream of air on the SOHC models).

3. From the inside of a cover of the air filter unscrew four bolts and remove two strengthening plates, then remove the air stream measuring instrument (see rice. Arrangement of bolts of fastening of the measuring instrument of a stream of air).

4. If necessary remove an air bell from the inside of a cover of the air filter.

Installation

Installation is made in the sequence, the return to removal taking into account the next moments...

PERFORMANCE ORDER

1. At installation of an air bell use new laying.

2. Apply the means interfering unscrewing of bolts on a carving of four bolts of fastening of the measuring instrument of a stream of air.

home