Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.29. Fuel nozzle (Multec system)

Removal

Detachment of the electric socket from a fuel nozzle on system of injection of Multec fuel

Unscrewing of the screw of fastening of the holder of a fuel nozzle

PERFORMANCE ORDER
1. Take off pressure in fuel system.
2. Remove the heater block.
3. Remove a weight wire from the accumulator.
4. Disconnect the electric socket from a fuel nozzle (see rice. A detachment электричес whom the socket from a fuel nozzle on system of injection of Multec fuel).
5. Unscrew the screw, the fixing holder of a fuel nozzle to the top part of the case of a throttle. Remove the holder and a nozzle (see rice. Unscrewing of the screw of fastening of the holder of a fuel nozzle). Remove condense telny rings.

Installation

Arrangement of sealing rings on a fuel nozzle

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal taking into account the next moments:

– at installation of a fuel nozzle use new sealing rings, for simplification of installation of a fuel nozzle grease sealing rings (see rice. An arrangement of sealing rings on a fuel nozzle);
– establish a fuel nozzle in such situation that the electric socket of a nozzle was directed to a back part of the car;
– before a vvinchivaniye of the screw of fastening of the holder of a fuel nozzle apply means on a screw carving, I interfere with a neck to unscrewing of the screw;
– include ignition and check fuel system for existence of leaks which need to be eliminated before start of the engine.