The device, service, repair Vektr's Opel And - 7.12. The fuel pump installed out of the fuel tank//1988-1995 /

Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775 24bec775



7.12. The fuel pump installed out of the fuel tank

Removal

Detachment of the electric socket from the fuel pump

PERFORMANCE ORDER
1. Depending on model the fuel pump can be installed on an arm under a back part of the car or on the right side of the car about a niche for a spare wheel or before the fuel tank.
2. Remove a weight wire from the accumulator.
3. Prepare the corresponding capacity for collecting fuel after removal of the fuel pump.
4. Disconnect the electric socket from the fuel pump (see rice. A detachment of the electric socket from the fuel pump).
5. Using clips, press fuel hoses from two parties of the fuel pump for reduction of losses of fuel after a detachment of hoses.
6. Weaken collars and remove fuel hoses from the fuel pump.
7. Weaken a bolt of fastening of a clip and remove the fuel pump from an arm.

Installation

Installation of the fuel pump
At installation of the fuel pump the plug of a clip has to rest against a flange on a pump housing.

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal. You make installation of the pump according to tags on a pump housing. Insert the pump into the rubber plug of a clip against the stop it in a flange on the case (see rice. Installation of the fuel pump).
2. Start the engine and check fuel system for existence of leaks. In the presence of fuel leak immediately switch off the engine and remove the cause of leak.