Opel Vectra A
since 1988-1995 release
Repair and operation of the car
Vektr's Opel And
+
1. Maintenance instruction
+
1.1 Maintenance
+
2. Engine
+
3. Repair of DOHC engines
+
4. Repair of the diesel engine
+
5. Cooling system
+
6. Fuel system
+
7. The fuel and exhaust system of models with system of injection of fuel
+
8. Exhaust system and system of decrease in toxicity of exhaust gases
+
9. Fuel systems of the diesel engine
-
10. Engine electrical systems
10.2. General information
10.3. System of ignition
10.4. Check of system of ignition
10.5. Rules of care of the accumulator
10.6. Check of the accumulator
10.7. Accumulator charging
10.8. Accumulator
10.9. System of charging
10:10. Generator
10:11. Driving belt of the generator
10:12. Removal and installation of the generator
10:13. Generator brushes
10:14. BOSCH generator
10:15. Small-sized DELCO-REMY generator
10:16. System of start of the engine
10:17. Starter
10:18. Removal and installation of a starter
10:19. Ignition coil
10:20. Cover and rotor of the distributor of ignition
10:21. Distributor of ignition (SOHC model)
10:22. Distributor of ignition (DOHC model)
+
10:23. Repair of the distributor of ignition
10:24. Check and adjustment of a corner of an advancing of ignition
10:25. Fine tuning of the moment of ignition under the used fuel grade
10:26. Electronic modules
10:27. MSTS-i elements
10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l)
10:29. Motronic system elements
10:30. Sensor of a detonation (DOHC model)
10:31. DIS module
10:32. Sensor of phases of the camshaft (C20 XE engine)
10:33. System of prestarting heating
10:34. Glow plugs
+
11. Transmission
+
12. Mechanical transmission
+
13. Automatic transmission
+
14. Power shafts
+
15. Brake system
+
16. Suspension bracket
+
17. Body
+
18. Electric equipment
+
19. Check of malfunctions
10:18. Removal and installation of a starter
Removal
Places of connection of an electrical wiring to the traction relay of a starter
Arrangement of a bolt of fastening of an arm of support of a reception exhaust pipe and starter on models of 1,6 l
Arrangement of bolts of fastening of a starter on model of 1,6 l
PERFORMANCE ORDER
1.
Remove a weight wire from the accumulator.
2.
Tighten the emergency brake, then lift a forward part of the car and record on supports.
3.
On models with DOHC engines remove the lower protective plate of the engine.
4.
Mark, then disconnect an electrical wiring from the traction relay (see rice.
Places of connection of an electrical wiring to the traction relay of a starter
).
5.
In the presence unscrew a bolt, the fixing arm of support of a reception exhaust pipe and a starter to the block of cylinders of the engine (see rice.
An arrangement of a bolt of fastening of an arm of support of a reception exhaust pipe and a starter on models of 1,6 l
).
6.
Unscrew two bolts of fastening of a starter. Keep in mind that the bolt located from the transmission can fix an arm of a plait of wires (see rice.
An arrangement of bolts of fastening of a starter on model of 1,6 l
).
7.
Remove a starter.
Installation
PERFORMANCE ORDER
1.
Installation is made in the sequence, the return to removal.
2.
Check that the arm of a plait of wires is established into place and tighten fastening bolts the required moment.
home
