The device, service, repair Vektr's Opel And - 10.13. Generator brushes//1988-1995 /

Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrical systems
   10.2. General information
   10.3. System of ignition
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Check of the accumulator
   10.7. Accumulator charging
   10.8. Accumulator
   10.9. System of charging
   10:10. Generator
   10:11. Driving belt of the generator
   10:12. Removal and installation of the generator
   10:13. Generator brushes
   10:14. BOSCH generator
   10:15. Small-sized DELCO-REMY generator
   10:16. System of start of the engine
   10:17. Starter
   10:18. Removal and installation of a starter
   10:19. Ignition coil
   10:20. Cover and rotor of the distributor of ignition
   10:21. Distributor of ignition (SOHC model)
   10:22. Distributor of ignition (DOHC model)
   + 10:23. Repair of the distributor of ignition
   10:24. Check and adjustment of a corner of an advancing of ignition
   10:25. Fine tuning of the moment of ignition under the used fuel grade
   10:26. Electronic modules
   10:27. MSTS-i elements
   10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l)
   10:29. Motronic system elements
   10:30. Sensor of a detonation (DOHC model)
   10:31. DIS module
   10:32. Sensor of phases of the camshaft (C20 XE engine)
   10:33. System of prestarting heating
   10:34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
24bec775 24bec775



10:13. Generator brushes

THE DELCO-REMY GENERATOR (EXCEPT SMALL-SIZED)

Removal

Removal of a forward cover of the DELCO-REMY generator

Arrangement of contact rings of a rotor on the DELCO-REMY generator

DELCO-REMY generator
And – nuts of fastening of wires of a winding of the stator;
In – screws of fastening of the brush holder/regulator of tension

PERFORMANCE ORDER
1. Remove the generator.
2. Using a chertilka, note the mutual provision of forward and back covers of the generator.
3. Unscrew three coupling bolts and remove a forward cover and a rotor from a back cover (see rice. Removal of a forward cover of the DELCO-REMY generator).
4. Check a condition of contact rings of the generator and, if necessary, smooth out them a small emery paper (see rice. An arrangement of contact rings of a rotor on the DELCO-REMY generator).
5. Unscrew three nuts, the fixing stator winding wires to the rectifier block, and remove the stator (see rice. DELCO-REMY generator).
6. Unscrew the screw and remove the block of rectifiers.
7. Unscrew two screws and remove tension brush holder/regulator from a back cover. Note an arrangement of the isolating washers under heads of screws.
8. Check smoothness of movement of brushes in guides and measure dyne of brushes.
9. For replacement of brushes unsolder contacts of old brushes from the brush holder and on their place solder new.
10. Check smoothness of movement of brushes in guides.

Installation

Extraction of a drill for release of brushes of the DELCO-REMY generator

PERFORMANCE ORDER
1. Before installation of brush holders record brushes in the wrung-out situation, using a steel wire or a drill.
2. Install brush holders so that the wire or a drill came out through an opening in a back cover of the generator. Fix the brush holder by screws.
3. Install the vypryamitelny block and a winding of the stator in a back cover and fix by nuts and the screw.
4. Establish a rotor in a back cover of the generator, then, according to earlier put tags establish a forward cover. Screw in three coupling bolts.
5. Take a wire or a drill from an opening in a back cover, at the same time brushes will fall by contact rings of a rotor (see rice. Extraction of a drill for release of brushes of the DELCO-REMY generator).
6. Install the generator.