Opel Vectra A

since 1988-1995 release

Repair and operation of the car


Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Windscreen washer/screen wiper switch
   18.9. Switches on the dashboard
   18:10. Switch of adjustment of provision of an external mirror
   18:11. Switch of the electric drive of the hatch
   18:12. The switch of illumination of salon installed in a door rack
   18:13. Switch of lighting of the luggage compartment
   18:14. Stoplight switch.
   18:15. Switch of a control lamp of the emergency brake
   18:16. Oil pressure sensor
   18:17. Lighter illumination
   18:18. Hours
   18:19. A front seat with heating
   18:20. Combination of devices
   18:21. Elements of a combination of devices
   18:22. Elements of the on-board computer
   18:23. Elements of a control and management system
   18:24. Sound signal
   18:25. Lamp of illumination of salon
   18:26. Replacement of bulbs of internal lighting
   18:27. Headlight
   18:28. Engine of the proofreader of light of headlights
   18:29. Adjustment of light of headlights
   18:30. System of reduction of intensity of light of headlights
   18:31. Forward index of turns
   18:32. Side repeater of turns
   18:33. Forward fog light
   18:34. Back lamps
   18:35. Lamp of illumination of registration plate
   - 18:36. Replacement of bulbs of external lighting
      18.36.1. Headlights
      18.36.2. Forward dimensional lamp
      18.36.3. Forward index of turns
      18.36.4. Side repeater of turns
      18.36.5. Forward fog light
      18.36.6. Back lamp
      18.36.7. Lamp of illumination of registration plate
   18:37. Replacement of brushes of a screen wiper
   18:38. Screen wiper levers
   18:39. Washer jets
   18:40. Engine and drafts of a screen wiper
   18:41. Engine of a screen wiper of a back door
   18:42. Headlight screen wiper engine
   18:43. Windscreen washer tank
   18:44. Windscreen washer pump
   18:45. Unidirectional valve of a washer of headlights
   18:46. Elements of window regulators with the electric drive
   18:47. Programming of a control system of window regulators
   18:48. Elements of the central blocking of doors
   18:49. Antenna
   18:50. An antenna mast with the electric drive
   18:51. Loudspeakers
   18:52. Radio tape recorder
   18:53. Hatch drive electric motor
   18:54. Speedometer drive cable
   18:55. Anticreeping alarm system
   18:56. Elements of the anticreeping alarm system
   18:57. Safety cushion
   18:58. A safety cushion from the driver
   18:59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit of safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions


24bec775


18.36.6. Back lamp

Removal

Extraction of the holder of lamps of a back lamp

Removal of a lamp from the holder of lamps of a back lamp

PERFORMANCE ORDER
1. Working in the luggage compartment, uncover a back part of a lamp.
2. Release a clamp in the top part of the holder of lamps and take the holder from a lamp (see rice. Extraction of the holder of lamps of a back lamp).
3. Take lamps from the holder (see rice. Removal of a lamp from the holder of lamps of a back lamp). Keep in mind that the stoplight lamp / dimensional light has an adjusting ledge in order that the lamp could be established only in one situation.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.