Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Windscreen washer/screen wiper switch
   18.9. Switches on the dashboard
   18:10. Switch of adjustment of provision of an external mirror
   18:11. Switch of the electric drive of the hatch
   18:12. The switch of illumination of salon installed in a door rack
   18:13. Switch of lighting of the luggage compartment
   18:14. Stoplight switch.
   18:15. Switch of a control lamp of the emergency brake
   18:16. Oil pressure sensor
   18:17. Lighter illumination
   18:18. Hours
   18:19. A front seat with heating
   18:20. Combination of devices
   18:21. Elements of a combination of devices
   18:22. Elements of the on-board computer
   18:23. Elements of a control and management system
   18:24. Sound signal
   18:25. Lamp of illumination of salon
   18:26. Replacement of bulbs of internal lighting
   18:27. Headlight
   18:28. Engine of the proofreader of light of headlights
   18:29. Adjustment of light of headlights
   18:30. System of reduction of intensity of light of headlights
   18:31. Forward index of turns
   18:32. Side repeater of turns
   18:33. Forward fog light
   18:34. Back lamps
   18:35. Lamp of illumination of registration plate
   + 18:36. Replacement of bulbs of external lighting
   18:37. Replacement of brushes of a screen wiper
   18:38. Screen wiper levers
   18:39. Washer jets
   18:40. Engine and drafts of a screen wiper
   18:41. Engine of a screen wiper of a back door
   18:42. Headlight screen wiper engine
   18:43. Windscreen washer tank
   18:44. Windscreen washer pump
   18:45. Unidirectional valve of a washer of headlights
   18:46. Elements of window regulators with the electric drive
   18:47. Programming of a control system of window regulators
   18:48. Elements of the central blocking of doors
   18:49. Antenna
   18:50. An antenna mast with the electric drive
   18:51. Loudspeakers
   18:52. Radio tape recorder
   18:53. Hatch drive electric motor
   18:54. Speedometer drive cable
   18:55. Anticreeping alarm system
   18:56. Elements of the anticreeping alarm system
   18:57. Safety cushion
   18:58. A safety cushion from the driver
   18:59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit of safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions


24bec775


18:21. Elements of a combination of devices

GENERAL INFORMATION

Remove a combination of devices.

CONTROL LAMPS AND LIGHTING LAMPS OF THE COMBINATION OF DEVICES

Removal

Removal of a bulb with the boss from a combination of devices

PERFORMANCE ORDER
1. From a reverse side of a combination of devices turn a cartridge of the corresponding lamp clockwise of an arrow and take it from the printed circuit board (see rice. Removal of a bulb with the boss from a combination of devices).
2. Lamps are built in in a cartridge, and replacement them it is necessary to make as the block.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.

VOLTAGE STABILIZER

Removal

Voltage stabilizer arrangement on the printed circuit board of a combination of devices

PERFORMANCE ORDER
1. From a reverse side of a combination of devices unscrew the screw and remove a stabiliz of Torahs of tension from contacts of the printed circuit board (see rice. A voltage stabilizer arrangement on the printed circuit board of a combination of devices).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.

INDEXES OF FUEL AND TEMPERATURE - MODELS OF A LOW SERIES

Removal

Removal of a forward frame of a combination of devices

PERFORMANCE ORDER
1. Remove the button of zeroing of the daily counter from the forward party of a combination of devices.
2. In the top part of a combination of devices release two clamps and remove a forward frame of a combination of devices (see rice. Removal of a forward frame of a combination of devices).
3. Unscrew two nuts and take the corresponding index from a combination of devices.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.

INDEXES OF FUEL AND TEMPERATURE - MODELS OF A HIGH SERIES

Removal and installation of indexes of fuel and temperature is made in the same way, as well as on models of a low series except that indexes fasten four nuts.

TACHOMETER

Arrangement of nuts of fastening of a tachometer

Removal and installation of a tachometer is made in the same way, as well as indexes of fuel and temperature except that the tachometer fastens three nuts (see rice. Arrangement of nuts of fastening of a tachometer).

SPEEDOMETER

Removal

Arrangement of screws of fastening of a speedometer

PERFORMANCE ORDER
1. Remove the button of zeroing of the daily counter from the forward party of a combination of devices.
2. In the top part of a combination of devices release two clamps and remove a forward frame of a combination of devices.
3. From the back party of a combination of devices unscrew four screws and remove a speedometer (see rice. Arrangement of screws of fastening of a speedometer).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.

PRINTED CIRCUIT BOARD

Removal

PERFORMANCE ORDER
1. Remove all lamps, indexes and the voltage stabilizer from a combination of devices.
2. Being careful, remove the printed circuit board from a combination of devices.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.