Opel Vectra A

since 1988-1995 release

Repair and operation of the car

Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Windscreen washer/screen wiper switch
   18.9. Switches on the dashboard
   18:10. Switch of adjustment of provision of an external mirror
   18:11. Switch of the electric drive of the hatch
   18:12. The switch of illumination of salon installed in a door rack
   18:13. Switch of lighting of the luggage compartment
   18:14. Stoplight switch.
   18:15. Switch of a control lamp of the emergency brake
   18:16. Oil pressure sensor
   18:17. Lighter illumination
   18:18. Hours
   18:19. A front seat with heating
   18:20. Combination of devices
   18:21. Elements of a combination of devices
   18:22. Elements of the on-board computer
   18:23. Elements of a control and management system
   18:24. Sound signal
   18:25. Lamp of illumination of salon
   18:26. Replacement of bulbs of internal lighting
   18:27. Headlight
   18:28. Engine of the proofreader of light of headlights
   18:29. Adjustment of light of headlights
   18:30. System of reduction of intensity of light of headlights
   18:31. Forward index of turns
   18:32. Side repeater of turns
   18:33. Forward fog light
   18:34. Back lamps
   18:35. Lamp of illumination of registration plate
   + 18:36. Replacement of bulbs of external lighting
   18:37. Replacement of brushes of a screen wiper
   18:38. Screen wiper levers
   18:39. Washer jets
   18:40. Engine and drafts of a screen wiper
   18:41. Engine of a screen wiper of a back door
   18:42. Headlight screen wiper engine
   18:43. Windscreen washer tank
   18:44. Windscreen washer pump
   18:45. Unidirectional valve of a washer of headlights
   18:46. Elements of window regulators with the electric drive
   18:47. Programming of a control system of window regulators
   18:48. Elements of the central blocking of doors
   18:49. Antenna
   18:50. An antenna mast with the electric drive
   18:51. Loudspeakers
   18:52. Radio tape recorder
   18:53. Hatch drive electric motor
   18:54. Speedometer drive cable
   18:55. Anticreeping alarm system
   18:56. Elements of the anticreeping alarm system
   18:57. Safety cushion
   18:58. A safety cushion from the driver
   18:59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit of safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions

18:56. Elements of the anticreeping alarm system

CONTROL UNIT

Removal

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Remove the lower finishing of the dashboard from the driver.

3. If necessary remove the panel of finishing of deepening for legs.

4. Unscrew a bolt of fastening of the control unit, then disconnect from it the electric socket and take the block from interior of the car.

Installation

PERFORMANCE ORDER

1. Installation is made in the sequence, the return to removal.

ULTRASONIC SENSOR

Removal

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Remove internal finishing from the central rack.

3. Being careful, remove the panel of finishing of the ultrasonic sensor and lower it down.

4. Disconnect the electric socket and take the ultrasonic sensor from interior of the car.

Installation

PERFORMANCE ORDER

1. Installation is made in the sequence, the return to removal.

SENSOR OF OPENING OF THE COWL

Removal

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. The screw-driver release a clamp in the basis of contact of the sensor and take contact.

3. Disconnect the electric socket of contact and remove the sensor.

Installation

PERFORMANCE ORDER

1. Installation is made in the sequence, the return to removal.

home

QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE