Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.37. Sensor of a detonation (Simtec system)

Removal

Sensor of a detonation of system of injection of Simtec fuel

1 – sensor;

2 – bolt


PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Disconnect electric sockets from the sensor of temperature of the air coming to the engine and the measuring instrument of a stream of warm air.
3. Remove hoses of ventilation of a case.
4. Remove hoses of supply of cooling liquid from the branch pipe coming to the engine of air, the tape measuring instrument of mass of a stream of warm air together with an air branch pipe from the top part of the air filter and the case of a throttle.
5. Using a screw-driver edge, release brackets of fastening of nozzles of the first and fourth cylinders in strips of the socket and at the same time lift strips. From a reverse side of strips there are six connections, four of which are intended for fuel nozzles.
6. Disconnect electric wires of the sensor of a detonation from a socket strip.
7. Tie a piece of a wire 1 m long to the electric socket of the sensor of a detonation.
8. Remove the detonation sensor from the block of cylinders of the engine (see the drawing).
9. Untie an additional wire from the electric socket of the sensor of a detonation.

Installation

Installation is made in the sequence, the return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Clear the interfaced surfaces of the sensor of a detonation and the block of cylinders of the engine. For fastening of the sensor of a detonation use only standard bolts and washers.
2. Being careful, install the detonation sensor on the block of cylinders and fix by a bolt, having tightened it the required moment.
3. Arrange a detonation sensor electrical wiring between ledges on an inlet collector. Untie an additional wire from the electric socket.
4. Insert the electric socket of the sensor of a detonation into a strip of sockets.
5. Arrange spring brackets of nozzles so that they did not interfere with gearing of strips of sockets. Check that between a strip of sockets and a nozzle there was a reliable contact.
6. Record strips of connecting sockets before the heard click.
7. Check a condition of hoses and reliability of fastening by their collars.