Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.23. Sensor of provision of a butterfly valve

GENERAL INFORMATION

Unscrewing of the screw of fastening of the sensor of provision of a butterfly valve on the early SOHC models

Removal

SOHC MODELS

Detachment of the electric socket from the sensor of provision of a butterfly valve on the early SOHC models

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Disconnect the electric socket from the sensor of provision of a butterfly valve (see rice. A detachment of the electric socket from the sensor of provision of a butterfly valve on the early SOHC models).
3. Unscrew the screw of fastening of the sensor and take the sensor of provision of a butterfly valve from the throttle case.

DOHC MODELS

Detachment of the electric socket from the sensor of provision of a butterfly valve on the DOHC models

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Disconnect the electric socket from the air stream measuring instrument. Remove a sealing ring.
3. Weaken a collar, the fixing main air branch pipe by the right end of the measuring instrument of a stream of air.
4. Unscrew four bolts fixing an air chamber to the throttle case. Raise an air chamber from the case of a throttle and in the basis of an air chamber disconnect a hose, then remove assembly of an air chamber / measuring instrument of a stream of air.
5. Disconnect the electric socket from the sensor of provision of a butterfly valve (see rice. A detachment of the electric socket from the sensor of provision of a butterfly valve on the DOHC models).
6. Unscrew two screws and take the sensor of provision of a butterfly valve from the throttle case.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.
2. On models with system of injection of M4.1 Motronic fuel before tightening of screws of fastening of the sensor of provision of a butterfly valve adjust position of the sensor as follows:

– turn the sensor case counterclockwise before emergence of notable resistance and tighten fastening screws;
– at the time of opening and the moment of closing of a butterfly valve from the sensor has to be heard click;
– if necessary adjust position of the sensor of a butterfly valve so that when opening a butterfly valve from the sensor the click was heard.

3. On models with system of injection of Motronic M fuel 1.5 at installation of the sensor adjustment as the sensor can be installed only in one situation is not required.