Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.19. Accelerator cable

Removal

Removal of a cable of an accelerator from the lever of a butterfly valve

Removal of a sealing ring of a cover of a cable of an accelerator from an arm on an inlet collector

PERFORMANCE ORDER
1. The cable of an accelerator is removed similarly, as well as on models with the carburetor taking into account the next moments.
2. The air chamber is available not on all models.
3. The carburetor it is necessary to understand the case of a throttle as the word and to pay attention that the arm of a cable of an accelerator fastens bolts to an inlet collector.
4. The end of a cable of an accelerator can connect to the spherical hinge on the lever of a butterfly valve which is fixed by a bracket (see rice. Removal of a cable of an accelerator from the lever of a butterfly valve).
5. In the presence remove an air chamber.
6. In the presence, using flat-nose pliers, take the spring bracket fixing the spherical hinge of a cable of an accelerator to draft of a butterfly valve. Using a screw-driver edge, remove the end of a cable of an accelerator from draft.
7. Take a bracket of fastening and remove a sealing ring of a cover of a cable of an accelerator from an arm (see rice. Removal of a sealing ring of a cover of a cable of an accelerator from an arm on an inlet collector).
8. Working in interior of the car, remove the finishing panel in deepening for the driver's legs.
9. Remove an accelerator cable from the top part of a pedal of an accelerator for what delay a spring back and, using a screw-driver edge, take a cable from an accelerator pedal groove.
10. Using an edge of the thin screw-driver, take a sealing ring of a cable of an accelerator from a partition of a motor compartment. Tie to the end of a cable акселерато ра a long strong cord.
11. Take an accelerator cable through a partition in a motor compartment. Untie a cord from an accelerator cable, leaving it in a partition of a motor compartment.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal taking into account the next moments:

– using a thin cord, tighten an accelerator cable through a partition of a motor compartment;
– establish a sealing ring of a cable of an accelerator in a partition of a motor compartment;
– connect an accelerator cable to draft of a butterfly valve and a pedal of an akseler a Torah;
– check work of a butterfly valve and adjustment of a cable of an accelerator.

Adjustment

PERFORMANCE ORDER
1. Check height of installation of a pedal of an accelerator. Height of installation of a pedal of an accelerator can be changed, turning the persistent screw of a pedal. For access to the persistent screw of a pedal of an accelerator it is necessary to remove the lower finishing in a niche for the driver's legs. Height of installation of a pedal of an accelerator has to be such that when pressing a pedal of an accelerator against the stop the butterfly valve completely opened.
2. In a motor compartment check that axes of rotary drafts and spherical hinges were not worn-out and easily moved. At completely closed butterfly valve and a pedal of an accelerator in a starting position, the deflection of a cable of an accelerator has to be insignificant.
3. For carrying out adjustment take the bracket fixing a sealing ring of a cover of a cable of an accelerator in kronshty not and move an accelerator cable cover on the required distance.
4. Press an accelerator pedal against the stop and check that the butterfly valve is completely open. If the course of a pedal is not enough for full opening of a butterfly valve, rotating the persistent screw, raise a pedal of an accelerator and repeatedly check adjustment of a cable of an accelerator.
5. After carrying out adjustment of a cable of an accelerator establish all earlier removed elements.