Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. The fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit of temperature of the air coming to the engine
   7.7. The sensor of temperature of the air coming to the engine
   7.8. Removal of pressure in fuel system
   7.9. The fuel filter on models with the fuel pump out of the fuel tank
   7.10. The fuel filter on models with the pump in the fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump installed out of the fuel tank
   7.13. The fuel pump installed in the fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a fuel-filling mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of fuel mix on idling turns
   7.21. Fuel pressure regulator
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Air stream measuring instrument
   7.26. Measuring instrument of mass of a stream of air
   7.27. Tape measuring instrument of mass of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except the Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step engine of management of air supply (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor of a detonation (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


7.15. Pipe of a fuel-filling mouth

Removal

PERFORMANCE ORDER
1. Through a fuel-filling mouth pump out fuel from the fuel tank.
2. Lift the lower edge of the consolidation located around a jellied mouth and unscrew the fastening screw.
3. Lift a back part of the car and record on supports.
4. Unscrew a bolt of fastening of a pipe of a fuel-filling mouth to the car bottom. Cut connecting collars or brackets which fix other hoses to a pipe of a fuel-filling mouth. Release collars and disconnect hoses of filling of the fuel tank and ventilation from the lower end of a pipe of a fuel-filling mouth. Disconnect hoses of ventilation of small diameter from connecting couplings on the top end of a pipe.
5. Check that all elements connected to a pipe are removed or disconnected and remove a pipe of a fuel-filling mouth from under the car.
6. For check of operability of the valve interfering leak in a pipe of a fuel-filling mouth turn a pipe and fill in gasoline in the lower connecting coupling. If the valve is serviceable, gasoline should not follow on the other side of a pipe. If gasoline follows, so the valve is faulty and it is necessary to replace completely a pipe of a fuel-filling mouth.

Installation

Places of connection of hoses of ventilation to a pipe of a fuel-filling mouth

And – a hose of the coal filter;

In – a hose of ventilation of the fuel tank


PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal taking into account the next moments:

– check a condition of all hoses and collars of fastening and if necessary, replace them;
– connect hoses of ventilation of the fuel tank to connecting couplings in the top end of a pipe of a fuel-filling mouth, and also a hose from the coal filter to the top connecting coupling and the ventilation hose going from the fuel tank to the lower connecting coupling (see the drawing);
– replace all brackets and collars, the fixing hoses cut at removal to a pipe of a fuel-filling mouth;
– check that there was no leak of fuel at its filling in the fuel tank.