Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   - 16:35. Replacement of protection covers of steering transfer
      16.35.1. Steering transfer without amplifier of steering
      16.35.2. Steering transfer with the amplifier of steering
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


16.35.2. Steering transfer with the amplifier of steering

GENERAL INFORMATION

Prevention

At installation it is necessary to use new bolts of fastening of a clip of steering transfer to a partition of a motor compartment and connecting plates bolts of fastening of steering thirsts for steering transfer.

At connection of pipelines it is necessary to use new sealing rings.


Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. On models with the engine with карбюрато rum remove the air filter. On a part of models for access to the right clip of fastening of steering transfer unscrew bolts, the fixing broad tanks and the main brake cylinder.
3. Establish forward wheels in situation for the movement directly forward.
4. Disconnect hoses on the left side of steering transfer and close a hose and an opening for a hose suitable traffic jams.
5. In order that it was possible to remove steering transfer, remove the relay block on the left side of a motor compartment.
6. Using a screw-driver edge as the lever, remove the fixing plate from heads of the bolts fixing steering thirst for steering transfer, then unscrew bolts and remove washers and a plate.
7. If steering transfer has the shock-absorber, unscrew the bolts fixing a clip of steering transfer and remove the shock-absorber.
8. Remove the lower panel of finishing in deepening for the driver's legs.
9. On models with adjustment of a tilt angle of a steering column move a steering column to the top situation.
10. Unscrew tightening the bolt fixing the elastic coupling to a steering shaft.
11. In a motor compartment unscrew bolts, the fixing two clips of steering transfer to a partition of a motor compartment, then on the left side take steering transfer. Keep in mind that on some models wires and hoses which before removal of steering transfer need to be disconnected can be attached to steering transfer.
12. It is not recommended to make independently repair of steering transfer with the amplifier of steering.
13. For elimination of leaks in junctions of hydraulic tubes it is enough to replace sealing rings.
14. It is independently possible to replace the protection cover of steering transfer.
15. You do not make adjustment of the steering mechanism with the amplifier of steering.

Installation

Installation is made in the sequence, the return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Establish a gear lath of steering transfer to the central situation. For this purpose count the speed of a shaft of steering transfer on which it is necessary to turn a shaft for movement of a gear lath from one extreme situation in another. Turn a shaft of steering transfer from extreme situation on a half of the counted turns therefore the gear lath will be established precisely on the center.
2. For fastening of clips of steering transfer to a partition of a motor compartment, it is necessary to use new bolts.
3. At installation it is necessary to use the new fixing plate which is established on heads of bolts of fastening of steering drafts.
4. Connect the elastic coupling to a steering shaft, at the same time top tightening the bolt of the elastic coupling has to settle down horizontally.
5. Connect hoses with new sealing rings to steering transfer.
6. Fill in fresh liquid in гидравличес I forge system of the amplifier of steering and remove air from system.