Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   + 16:35. Replacement of protection covers of steering transfer
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


16:22. Check of system of the self-leveled back suspension bracket

PERFORMANCE ORDER
1. On completely empty car install the manometer on the air valve and check that pressure in a control system of the self-leveled back suspension bracket makes 0,8 bars. Otherwise adjust pressure.
2. Install the car on the flat horizontal platform and measure distance from the center of a rear bumper to the earth. Subtract 50 mm from the measured distance and write down the received result.
3. Completely load the car and check that the bumper of the car was established at earlier calculated height. If necessary lift pressure in system, but do not exceed it higher than 5 bars.
4. Completely unload the car and reduce pressure in system to 0,8 bars and check that the bumper was established on originally measured height.
5. Do not operate the empty car with high pressure in a control system self-leveled a back suspension bracket.