Opel Vectra A

since 1988-1995 release

Repair and operation of the car

Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward lower frame
   16.5. Rack of a forward suspension bracket
   16.6. Lower lever of a forward suspension bracket
   16.7. Replacement of plugs of the lower lever of a forward suspension bracket
   16.8. Spherical hinge of the lower lever of a forward suspension bracket
   16.9. Forward stabilizer of cross stability
   16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost
   16:11. Adjustment of the bearing of a back wheel (SOHC model)
   16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16:13. Replacement of the hug bearing of a back wheel (model since 1993)
   16:14. A nave of a back wheel (model with the SOHC engine)
   16:15. Back shock-absorber
   16:16. Replacement of rubber elements of fastening of the back shock-absorber
   16:17. Springs of a back suspension bracket (SOHC model)
   16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16:19. Back stabilizer of cross stability
   16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16:21. The fastener of a back nave (model with SOHC engines)
   16:22. Check of system of the self-leveled back suspension bracket
   16:23. Control system elements self-leveled a back suspension bracket
   16:24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16:25. A nave of a back wheel (model with DOHC engines)
   16:26. Knot of a back suspension bracket (model with DOHC engines)
   16:27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16:28. Back stabilizer of cross stability
   16:29. Steering wheel
   16:30. Centering of a steering wheel
   16:31. Replacement of the elastic coupling of a shaft of steering transfer
   16:32. Steering column
   16:33. Repair of a steering column
   16:34. Shock-absorber of steering transfer
   + 16:35. Replacement of protection covers of steering transfer
   16:36. Removal of air from system of steering with the amplifier
   16:37. Pump of the amplifier of steering
   16:38. Popolnitelny tank of system of the amplifier of steering
   16:39. Pipes of cooling of liquid of the amplifier of steering
   16:40. Tips of steering draft
   16:41. Steering draft
   16:42. Angles of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions

16:14. A nave of a back wheel (model with the SOHC engine)

GENERAL INFORMATION

Prevention

At installation it is necessary to use the new forelock fixing a nave nut from unscrewing.

Installation of a nave / brake disk

Installation of a washer on a nave / a brake disk

Nuts of fastening of a nave / brake disk

MODELS WITH BACK DRUM BRAKES

Removal

PERFORMANCE ORDER

1. In the presence take off a wheel cap, then weaken bolts of fastening of a back wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.

2. Remove the brake drum.

3. Using a screw-driver edge as the lever, take off a dustproof cap of a nave.

4. Take the forelock fixing a nave nut from unscrewing, then unscrew a nut of fastening of a nave. For deduction of a nave from a provorachivaniye when unscrewing a nut of fastening of a nave screw in two bolts of fastening in a nave and insert mount between bolts.

5. Remove a persistent washer and a nave from a nave pin.

Installation

PERFORMANCE ORDER

1. Establish a nave and an internal ring of the external bearing on a nave pin. At the same time do not damage the sealing ring established from the inside of a nave.

2. Establish a persistent washer and screw a nut of fastening of a nave, then adjust a side play of the bearing of a back wheel.

3. Using the new forelock, record a nut of fastening of a nave from unscrewing, then establish a dustproof cap of a nave.

4. Install the brake drum and check adjustment of a cable of the emergency brake.

5. Lower the car on the earth and tighten bolts of fastening of a wheel the required moment.

MODELS WITH BACK DISK BRAKES

Removal

PERFORMANCE ORDER

1. On models with back disk brakes the nave and a brake disk represent one detail.

2. In the presence take off a wheel cap, then weaken bolts of fastening of a back wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.

3. Remove a brake support, without disconnecting from it a brake hose and using a soft wire, suspend a support to a back suspension bracket.

4. Using a screw-driver edge as the lever, take off a dustproof cap of a nave.

5. Take the forelock fixing a nave nut from unscrewing, then unscrew a nut of fastening of a nave. For deduction of a nave from a provorachivaniye when unscrewing a nut of fastening of a nave screw in two bolts of fastening in a nave and insert mount between bolts.

6. Unscrew a nut and remove from a nave pin a washer and a nave / a brake disk. If the nave / a brake disk are not removed, take away from the brake drum of a block of the emergency brake for what insert the screw-driver through an adjusting opening in a nave / a brake disk and turn a regulator wheel.

Installation

PERFORMANCE ORDER

1. Establish a nave / a brake disk and an internal ring of the external bearing on a nave pin. At the same time do not damage the sealing ring established from the inside of a nave / a brake disk.

2. Establish a persistent washer and screw a nut of fastening of a nave, then adjust a side play of the bearing of a back wheel.

3. Using the new forelock, record a nut of fastening of a nave from unscrewing, then establish a dustproof cap of a nave.

4. Check adjustment of the emergency brake and establish a brake support.

5. Lower the car on the earth and tighten bolts of fastening of a wheel.