Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
- 12. Mechanical transmission
   12.2. General information
   12.3. Adjustment of draft of the mechanism of the choice of transfers
   12.4. Gear shifting lever knot
   12.5. Draft of the mechanism of the choice of transfers
   12.6. Gear shifting lever
   12.7. Protective cover of the lever of gear shifting
   12.8. Sealing rings of differential
   12.9. Sealing ring of an entrance shaft of the transmission
   12:10. Removal and installation of the transmission
   12:11. Repair of the transmission
   12:12. Speedometer drive
   12:13. Switch of lamps of a backing
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


12.3. Adjustment of draft of the mechanism of the choice of transfers

GENERAL INFORMATION

Prevention

After carrying out adjustment close a regulator opening in a cover of the mechanism of the choice of transfers by a new stopper.


Arrangement of the tightening bolt fixing a rod of the mechanism of the choice of transfers to draft

Extraction of a stopper from an opening for adjustment in a cover of the mechanism of the choice of transfers

Installation of a drill
At installation of a drill, it has to enter an opening in the lever of the choice of transfers.

Arrow on the gear shifting lever
The arrow on the lever of gear shifting has to be combined with a cut of elements of blocking of inclusion of transfer of a backing.

Gap between a hook and an emphasis
The gap between a hook (A) and an emphasis (V) has to make no more than 3 mm.

PERFORMANCE ORDER
1. In a motor compartment weaken tightening a bolt, the fixing rod of the mechanism of the choice of transfers to draft (see rice. Arrangement of the tightening bolt fixing a rod of the mechanism of the choice of transfers to draft). On models since 1993 the arrangement of a tightening bolt is changed and access to it is most convenient from under the car.
2. Take the stopper closing an opening for adjustment in a cover of the mechanism of the choice of transfers (see rice. Extraction of a stopper from an opening for adjustment in a cover of the mechanism of the choice of transfers).
3. Turn a rod of the mechanism of the choice of transfers counterclockwise so that the drill with a diameter of 4,5 mm inserted through an opening for adjustment in a cover of the mechanism of the choice of transfers entered an opening in the lever of the choice of transfers (see rice. Installation of a drill).
4. In interior of the car for access to the basis of the lever of gear shifting remove a protective cover of the lever of gear shifting from the central console.
5. The assistant has to hold the gear shifting lever in neutral situation in a point of inclusion of the first/second of transfers. At the same time the lever has to rest against an element of blocking of inclusion of transfer of a backing, and the arrow and a cut have to settle down as it is shown on rice. An arrow on the gear shifting lever
6. On models since 1993 after installation of the lever of gear shifting in situation for adjustment insert the second drill with a diameter of 4,5 mm into an opening in the gear shifting lever. At the same time there is a blocking of the lever of gear shifting for the period of adjustment and the help of the assistant is not required. In this position of the lever tighten tightening a bolt, the fixing rod of the mechanism of the choice of transfers to draft.
7. On models till 1993 check that the gap between a hook (A) and an emphasis (V) in the basis of the lever of gear shifting made no more than 3 mm (see rice. A gap between a hook and an emphasis).
8. Install a protective cover of the lever of gear shifting on the central console.
9. Take a drill from an opening for adjustment in a cover of the mechanism of the choice of transfers and close an opening a new stopper.
10. Check operation of the mechanism of the choice of transfers on single turns of the engine.