Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrical systems
10.2. General information
10.3. System of ignition
10.4. Check of system of ignition
10.5. Rules of care of the accumulator
10.6. Check of the accumulator
10.7. Accumulator charging
10.8. Accumulator
10.9. System of charging
10:10. Generator
10:11. Driving belt of the generator
10:12. Removal and installation of the generator
10:13. Generator brushes
10:14. BOSCH generator
10:15. Small-sized DELCO-REMY generator
10:16. System of start of the engine
10:17. Starter
10:18. Removal and installation of a starter
10:19. Ignition coil
10:20. Cover and rotor of the distributor of ignition
10:21. Distributor of ignition (SOHC model)
10:22. Distributor of ignition (DOHC model)
+ 10:23. Repair of the distributor of ignition
10:24. Check and adjustment of a corner of an advancing of ignition
10:25. Fine tuning of the moment of ignition under the used fuel grade
10:26. Electronic modules
10:27. MSTS-i elements
10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l)
10:29. Motronic system elements
10:30. Sensor of a detonation (DOHC model)
10:31. DIS module
10:32. Sensor of phases of the camshaft (C20 XE engine)
10:33. System of prestarting heating
10:34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions
|
HEI MODULE (MODELS 14 NV)
Removal The module is installed on a metal plate on the left side of a motor compartment under the ignition coil.
| PERFORMANCE ORDER |
| 1. Remove the ignition coil. |
| 2. Unscrew two screws and remove the module from a metal plate. |
| 3. Before installation of the module apply a thin film of heat-conducting paste on the interfaced surface of a metal plate. At installation of the new module in a set of the module there has to be Nye's heat conductor a paste. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
|
MSTS-i MODULE (MODELS 1,6 And 1,8 L)
Removal
MSTS-i module arrangement on model of 1,6 l
| PERFORMANCE ORDER |
| 1. The module is installed on a partition of a motor compartment over steering transfer (see rice. A MSTS-i module arrangement on model of 1,6 l). |
| 2. Remove a weight wire from the accumulator. |
| 3. For improvement of access remove an air chamber from the carburetor. |
| 4. Disconnect the electric socket from the module. |
| 5. Unscrew two nuts and remove the module from a partition of a motor compartment. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
|
MOTRONIC MODULE
Removal
Removal of the Motronic module on model of 2,0 l
Detachment of the electric socket from the Motronic module on model 2,0
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
|
|
|
