Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance + 2. Engine + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system + 6. Fuel system + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine - 10. Engine electrical systems 10.2. General information 10.3. System of ignition 10.4. Check of system of ignition 10.5. Rules of care of the accumulator 10.6. Check of the accumulator 10.7. Accumulator charging 10.8. Accumulator 10.9. System of charging 10:10. Generator 10:11. Driving belt of the generator 10:12. Removal and installation of the generator 10:13. Generator brushes 10:14. BOSCH generator 10:15. Small-sized DELCO-REMY generator 10:16. System of start of the engine 10:17. Starter 10:18. Removal and installation of a starter 10:19. Ignition coil 10:20. Cover and rotor of the distributor of ignition 10:21. Distributor of ignition (SOHC model) 10:22. Distributor of ignition (DOHC model) - 10:23. Repair of the distributor of ignition 10.23.2. Model 16 SV 10.23.3. DOHC models 10:24. Check and adjustment of a corner of an advancing of ignition 10:25. Fine tuning of the moment of ignition under the used fuel grade 10:26. Electronic modules 10:27. MSTS-i elements 10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l) 10:29. Motronic system elements 10:30. Sensor of a detonation (DOHC model) 10:31. DIS module 10:32. Sensor of phases of the camshaft (C20 XE engine) 10:33. System of prestarting heating 10:34. Glow plugs + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system + 16. Suspension bracket + 17. Body + 18. Electric equipment + 19. Check of malfunctions
|
Dismantling
Extraction of a cylindrical pin, the fixing distributor shaft drive plug on model 1,6 l (BOSCH distributor)
Removal of washers from an ignition distributor shaft
Removal of washers from an ignition distributor shaft on model 1,6 l (BOSCH distributor)
Extraction of a clamp of the electric socket (LUCAS distributor)
Detachment from a back part of the socket of the small socket on models 1,6 l (LUCAS distributor)
Unscrewing of screws of fastening of a basic plate
Extraction of a basic plate from the ignition distributor case on model 1,6 l (LUCAS distributor)
Arrangement of the screw of fastening of a basic plate on model 1,6 l (LUCAS distributor)
PERFORMANCE ORDER |
1. Using the hammer and a drift, beat out the cylindrical pin fixing the drive plug to a distributor shaft (see rice. Extraction of a cylindrical pin, the fixing distributor shaft drive plug on model 1,6 l (BOSCH distributor)). |
2. Remove the plug of the drive and a washer from an ignition distributor shaft (see rice. Removal of washers from an ignition distributor shaft). |
3. Take a distributor shaft together with the cylindrical screen with teeths from the case of the distributor and remove washers from a shaft (see rice. Removal of washers from an ignition distributor shaft on model 1,6 l (BOSCH distributor)). |
4. On the LUCAS distributor remove a spring clamp of the electric socket, then take the socket from the case of the distributor of ignition and from a reverse side of the socket disconnect the small electric socket (see rice. Extraction of a clamp of the electric socket (LUCAS distributor), the Detachment from a back part of the socket of the small socket on models 1,6 l (LUCAS distributor)). |
5. Unscrew screws and take a basic plate from the distributor case (see rice. Unscrewing of screws of fastening of a basic plate, Extraction of a basic plate from the ignition distributor case on model 1,6 l (LUCAS distributor), the Arrangement of the screw of fastening of a basic plate on model 1,6 l (LUCAS distributor)). |
|
Check
PERFORMANCE ORDER |
1. Check a condition of a cover of the distributor of ignition for existence of corrosion of contacts, black paths between contacts, and also integrity and smoothness of movement of coal contact in the center of a cover. With defects replace an ignition distributor cover. |
2. Check a state and fastening of metal contact of a rotor of the distributor. If the contact burned or its fastening weakened, replace a distributor rotor. In the presence, remove a deposit and traces of corrosion from contact, using a small file. |
3. Check a condition of a sealing ring in a back part of the distributor of ignition and, if necessary, replace it. |
|
Assembly
PERFORMANCE ORDER |
1. Assembly is made in the sequence, the return dismantling. At assembly correctly establish washers. Install the plug of the drive so that the ledge of the plug entered a groove in the top part of a shaft of the distributor. |
2. Install the ignition distributor, then check and, if necessary, adjust an ignition advancing corner. |
|
|
|